How to Replace a kia sportage replacement key (simply click Alonegocio)

For many kia sportage key replacement models keys, the key has the keyless entry system that is built into the key. This key is similar to the remote control, and can be exchanged with an Kia dealer.

Key fobs might stop working due to a variety of reasons, including a dead coin battery worn buttons signals, signal interference, water damage and a faulty receiver module. Here are some tips on how you can get your kia picanto car key replacement Sportage replacement key working again.

How do you replace the remote key or the smart key?

The battery inside your Kia's smart key will eventually need to be replaced, regardless of whether it's a remote or a push-to-start one, or a normal metal key that doesn't contain an electronic transponder. This is especially when the car displays a message that the smart key or remote is not powered by the battery.

This is a relatively easy process. To replace the battery in the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, pry the cover off. A small screw will be inside the key fob, which holds the battery in place. Utilizing a small screwdriver unscrew the screw and remove the old battery. Install the new battery and close the gap on the key fob.

When the key fob is equipped with a fresh battery and you've tested it, press the locks and unlock buttons. If the doors unlock and lock according to your expectations, then you're all set! You can now utilize the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you need to run some errands in Brandon.

Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a machine for programming that is available only to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) don't require programming. If your key requires to be reprogrammed, you must be aware of the number stamped on the key code tag and keep the number in a secure place.

How to replace the battery

If the Kia key fob is unable to respond to pressing the lock or unlock button, it's likely that the battery is insufficient. A weak battery can cause other issues, such as the check engine light coming on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a simple DIY project that requires just the most basic tools.

Before starting the process before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key pops out. This key can be inserted into the driver door handle to unlock your car.

To replace the battery on the key fob, take off the cover on the rear. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then orient the new battery to ensure that the "+" positive side faces you and the "negative" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid bending or damaging the contacts on the metal.

After the new battery has been installed, turn the key fob off and then on in the ignition several times until the door locks cycle. You can then test your kia key replacement's key fob again to make sure it's working properly.

How do you replace the smart key?

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference between the two is that the smart key is equipped with a small mechanical key blade hidden within it, whereas the standard fob doesn't. Both kinds of key fobs contain batteries that will eventually need to be replaced. Fortunately, it's an easy process that takes just two minutes.

Before you start it is essential to ensure that you are on a flat surface with good lighting and that your Kia is not on. Also, keep in mind that there are tiny parts inside the fob that could fall out if you are not careful.

The first step is to locate the small release button that is located on the backside of the fob. It could be an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob opened then you can remove the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After you're done, your key fob should be able to lock, unlock, and start your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car with just pressing a button. Like any other device like a key fob, the Kia may have issues. There are ways to resolve these issues and ensure that our key fobs are in good working order over the long haul.

One of the most common issues is a low or dead battery. This could cause the fob to stop working entirely or work intermittently. If this is the issue, replace the battery with an entirely new battery.

If this does not resolve the issue, try using the flathead screwdriver that is standard to push the plastic casing of the fob open. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed, replace it with a new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob and make sure it is working correctly. If the key fob isn't working, call an authorized locksmith or dealer to help resolve the problem. To avoid future lockouts, make sure you get an emergency key that can work in all of the trunk and door cylinders.