How to Repair Bifold Door Top Roller Guide

If your bifold door is squeaking then it's likely that they need some attention. They may require cleaning and lubricated or adjusted. The issue could be caused by a loose screw on the top pivot or the top roller guide.

This kit includes all the hardware required to restore your bi fold door repairs near me-fold closet door system to its best performance.

Remove the Door

Installing a set of internal bifold doors might seem like a complex and challenging task, but it's actually quite easy for DIYers with a few years of experience. The frame isn't the issue, but getting the doors to fold and close smoothly is. As bifold doors are complex machines, they could require some tweaking to ensure they are functioning correctly. It could be as easy as tightening a screw, or as complicated as taking off and replacing the pivot pin or roller.

Most of the time you can fix these issues with a couple of simple adjustments, without having to remove the doors. It is possible that your bifold doors are sliding or scraping the floor, or jumping out of track. In order to fix these issues, it isn't a big deal, and with three easy steps your bifold doors can be back in the blink of an eye.

One of the most common problems that internal repairing bifold doors doors encounter is sliding out of alignment. This can be due to loose screws, holes in the anchor/pivots, or a misaligned bifold door. Most times it can be fixed by making a few minor adjustments. However, if your door isn't moving in any way, you might require replacing it.

To remove the door, you'll need an screwdriver and perhaps a pair of pliers (to assist in loosening any pins that are tight to pivot). The screwdriver is used to disengage the locking levers on the bottom bracket for pivots. The pliers are used to take off the pin.

Once the top roller is free and the top roller is loose, you should be able to lift the door and swivel it downward in order to lift it out of its pivot brackets and track. It's usually a simple procedure, but be careful to not let the door strike the door frame. You should then be able to saw off the edge of the door that's scraping the floor, and sand it down until it's smooth. You can then repaint it or refinish it as required.

Remove the Roller Guide

This spring-loaded roller guides the mount on top of bifolding doors to facilitate smooth operation. It is designed specifically for Kenna frames, and will fit door panels that range from 1 inch to 1-3/8 inch thick. It is constructed of nylon, steel, and plastic components. It is able to replace an old guide.

Remove any screws holding the roller guide in place with a screwdriver. After that, carefully use your hands to pull it out of the frame. It could require some effort to lift the door, so make sure you ask an assistant to help.

After removing the guide, carefully cut off the remaining finish on the foot of the guide by using a razor to cut it from blank rod. This will make the guide foot much easier to remove and prevent any damage. The guide foot is extremely sharp, and it can cut or snag fingers.

It is possible to use some force to remove the guide, but you must be careful not to break or chip the foot. After you have separated the old guide from the rod blank, make sure to take out all of the epoxy and threads that remain where it was affixed. This will help avoid future problems with the guide.

After removing the old guide, try out your replacement by placing it in its permanent location and applying a few rotations of masking tape or some kind of guide tubing to keep it in its place. This will allow you to double-check the guide alignment and spacing to ensure that everything is in place. Whether you're eye-balling it or using the always accurate CRB Spine Finder and Deflection System, this step is important to prevent any issues in the future.

The final step is to replace the door. If the guide is in the right position and functions in the correct way, then you're ready to proceed. Remember that any screws or pins were removed or loosening must be replaced and tightened appropriately after you've finished.

Remove the Bottom Pivot

Bifold doors make a gorgeous addition to any home, but often they require a bit of tweaking or adjustment to remain in good shape. While some of the less critical problems can be solved with the doors in place, others will require them to be removed. This guide will show you how to remove the bifold internal door pins, rollers, and pivots.

Gathering your tools is the first step. Getting everything together prior to time will make it easier later on in the project. You'll need a screwdriver, pliers and maybe a wrench. A basic set of tools can be purchased at a reasonable cost at your local hardware store. Also, keep some wood glue in the back of your hand. This will come in handy if you have to glue any of the rollers back in the correct position.

Once you've got the tools, begin by opening the bifold doors and then loosening the top track bracket with your screwdriver. Once it's loose the door should be capable of sliding off the top track completely. It may take a small amount of jiggling, but it should pop right off the track.

The bottom pivot of the frame will have to be removed. It is best to do this from the outside of the house, so be sure to close any interior doors that are open. This will be much easier than trying to work from the inside. If the track at the bottom is in good shape, you'll be able to simply lift the door and then remove the track.

If the track is damaged, then you'll need to replace it. You can get replacement tracks for both swinging and repairing bifold doors closet doors from a local hardware store. If the track is seriously damaged then you may need to replace it completely.

After your track has been repaired or replaced it is time to test the doors for the proper operation. Make sure that they are able to move smoothly from position to position. You should also ensure that the edges of the door are parallel to the frame when it is closed. If they're not, you'll have to adjust the top pivot bracket and tighten or loosen the bottom set screw until the door's edge coincides perfectly with the frame.

Replace the Roller

Bifold doors neatly enclose closets or laundry rooms, as well as pantries, but only when they work properly. They comprise two door panels that are hinged and open using the track that is located at the top of the frame. Over time, the roller guide bearings can wear out and cause the doors to bow and rub against the floor. The roller guide can be replaced in a matter of minutes with basic tools.

The first step is to remove the guide roller from the door panel. This requires removal of the bottom pivot bolt and loosening the screw that holds the guide on its top. Once the guide is removed and the door panel is lifted up and out of its track. Next, loosen the nut that holds the top pivot bolt and employ a wrench to pull it out of the hole in the top header of the door frame.

A replacement top nylon roller guide that has a 7/8 inch diameter wheel and a steel base is available from Stanley, Cox or Acme. It is mounted on the top of bifold doors which are 1 to 1-3/8 inches thick. It comes spring-loaded and adjusts itself in the upper track to ensure smooth gliding.

Another issue that is common to bifold doors is that it scrapes against the floor when it is closed or opened. This can occur after installing carpet or other flooring materials which require the doors to be slightly raised to allow for clearance. This issue can be solved by removing the bottom pivot adjustment screws, loosening up the top track mounting screws, and moving the anchor/pivot.

A new set of top roller guides is a cheap solution to a problem that may make bifold doors difficult to operate. They're usually available at your local hardware store in the door section, but they're also available on the internet through a variety of vendors. You'll also require an elongated squeeze-clamp as well as a small container Elmer's wood adhesive, that is sold in large box stores. The clamp is used to keep the repair area closed tightly after the glue has been inserted and dried.