How to Replace a Saab 9-3 Key

The Saab 9-3 has a good variety of appeal to drivers. It has excellent visibility and a strong performance engine. It has a high safety rating.

It is important that you have two keys that work for your vehicle. It can be costly to replace a key if you lose it.

How to replace the ignition Key in the Saab9-3

You'll must replace your car key in case it isn't turning. This guide will explain how to replace the ignition key on the Saab 9-3. You will have to replace the key, get an updated reprogrammable phone, and then purchase a new casing for your key-fob.

Contrary to earlier models, modern Saab vehicles use a transponder on the key-fob rather than a physical key made of metal to unlock and start the car. The rechargeable batteries contained in the key-fob inevitably expire, and they can't hold any charge. This is especially relevant if you use the same key for the same lock.

The good part is that the battery is easily replaced by a professional locksmith. If you have the proper tools, and a little patience you can do it yourself. The first step involves separating the key-fob. This is accomplished by inserting a flathead screwdriver into the slot that is located in the middle of the case. The plastic is thin and it is susceptible to being damaged.

Once the case is open then you can prepare the new key by combining the lower section of the old key and the transponder and banana on the new key. This will ensure the new key is properly connected to your CIM and could be a major difference when replacing the sole key of your Saab 9-3.

How to replace the ignition Key on a Saab 900

Unless you have two keys, you'll need to remove the steering wheel and dashboard to gain access to the ignition. Start by disconnecting your negative battery cable. After the battery has been disconnected, you can take off the dashboard and trim pieces around the steering wheel. After the dashboard is removed, you can put a screwdriver into the opening at the back of the ignition switch and pull it out.

The ignition cylinder is fitted with a lock for keys that could stop the vehicle from starting if it does not have the key inside it. If the ignition switch on your 900 isn't functioning properly, check whether the key is inside the lock or in the barrel of ignition. It is also important to rotate your keys and keep them clean to prevent bent.

saab replacement key programming cars differ from other cars due to the fact that they do not have traditional metal keys. Instead, the car recognizes electronic signals coming from the key fob by using a special microchip in it.

If you lose only one key fob that is working, your dealer will charge you the cost of replacing your computer module (also known as the CIM). We can however reprogram your computer's EEPROM, and then prepare it to accept new keys without replacing it. You will save over 50% on the price of the dealer! This is the saab key fob Key PROGRAM. Find out more about it here!

How to replace the ignition Key in a Saab9-5

The metal portion of a traditional Saab key is simple to copy, and it's not much of an impediment against theft of a vehicle. The real protection is the electronic component inside the key-fob. It is equipped with a chip that detects the car when it's inserted into your ignition switch.

Saab's anti-theft system has been relying on this technology for more than 10 years. It's not quite as effective as a physical lock for your door, but it makes stealing your car a lot harder. That's why every saab key replacement bristol owner should keep a spare key on hand.

The majority of new Saabs come with two keys, but they can be added at the dealer's expense using a handheld device known as a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 cars, with more modern, newer features that require the use of a key-fob.

The dealer will replace the CIM or TWICE module in these cars if the keys are lost saab keys. They'll charge you top dollar for doing it. We can however reprogram the EEPROM on your computer and make it accept new keys, and not replace the expensive modules.

How do I replace the ignition Key on a replacement saab key XC90

If your SAAB 9-3 key fob starts having problems turning the lock barrel it could be time to replace it. The process is fairly simple and you don't even need to visit a dealer. You can complete the process at home, using a couple of simple tools.

It is first necessary to prepare the keys for your new car. Before you begin, ensure that the anti-theft system is disabled by placing blocks on the rear wheels and releasing the handbrake. Then, you can insert the key into the ignition and turn it to the on position that activates the accessories, but doesn't start the engine. Repeat this procedure 5 times, and then put the key in the "on" position.

The next step is to purchase a new case for your old key fob. They can be found at any auto parts store and they're typically quite affordable. Depending on the model, you could even buy them without electronics.

To open the case simply push the screwdriver with a flathead into the slot in the middle. Once you split the case, you'll be able to access all the internal electronics. Use a flathead screwdriver to gently pull out the electronic components.