Reasons Your fiat 500 replacement key fob 500 Key Fob Won't Work

A key fob for fiat key programmer 500 makes it easy to open doors and start your vehicle. However, there are a variety of reasons the fob could stop functioning. These include a dead battery, water damage, receiver module issues, or interference.

This listing is for a new fiat key replacement fiat 500 flip key repair 500x key, Botdb.win, Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob not functioning. Modern key fobs come with a limited range of operation, and should be within just a few feet of the vehicle to function. If you are not within your car and press the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a trusted brand like Panasonic Duracell or Energizer. They can be found in your local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while standing near your Fiat 500. The parking lights should light up and the key fob will operate the lock and unlock switch.

If the fob's key doesn't work after replacing the battery, it may have water damage that stops it from communicating with the receiver module in your car. Water damage can happen in a variety of ways, from an accidental splash to submerging the fob into salt water at the beach. If you suspect that your fob was exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If this doesn't work, your fob will probably need to be reset by an experienced auto locksmith or by the dealer.

Water Damage

Damage to the water supply can occur if you submerge the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to become shorted and eventually die. The fob getting wet is not an option but if you drop it in a cup of water or fail to remove it from your pants pocket prior to running the washer do not give up hope.

First take the battery off the fob. Clean the electronic chip with isopropyl ethanol or a similar product and dry it completely before replacing the battery. Then check the fob to see if it works. If the fob doesn't work, it may have to be changed. This is usually done by a dealer or professional auto locksmith.

If the key is older and has not been programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars can carry out this simple task. The locksmith will require the key to be cut to match your car's ignition. They will also need to program the fob into your car's system. This is a quick and affordable process that can be completed within the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop functioning is that it's out of range. The remote typically has an area of 30 feet or less, and if it's too far from your car, it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you've replaced the battery on your coin (commonly called a "button" or "watch") and the fob isn't working It could be because of an internal circuit board issue. Reprogramming your fob can resolve this issue. You can find the instructions on how to do this for most automobiles by searching YouTube or checking out the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in place. If they lose tension, it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle because of software or hardware issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram fiat 500 key fob your key fob. In some instances, they may need to install the software again in your body control module, as well.

Interference

In addition to a dead coin battery, the key fob may not be receiving or transmitting a signal due to interference. This could happen when the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob might not work could be due to a weak connection to the buttons or the internal chip, or water damage.

If the key fob stopped working one day out of the blue, or after trying everything you can at home to resolve it e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming, or using an alternative key fob. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands which are then read by the vehicle.

Fortunately, there's an easy way to reset every single system on board in your 500 and include the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will clear any residual electric current, and also restart the computer in your car. This can help you get your key fob to work again. If the issue persists, you should consult an expert technician. They can identify the exact cause of problems.