Replacement UPVC Door handles and hinges (this hyperlink)

Find the perfect handle for your door, whether you're replacing your existing handles or adding security. These upvc handle are easy to install and have the minimum 92mm center distance of multipoint locks.

The backplate's fixing centre as well as the keyhole/lever dimensions are the most important measurements. Make sure you compare these to your existing measurements prior to placing an order.

Lever/Pad

Lever pad door handles are made up of a lever handle on one side and a paddle shaped handle on the other. They are intended for use with key wind locks. However they can be affixed to multipoint split spindle door locks.

Our range of upvc handles lever pads are available in a variety of finishes and these will be shown in the drop-down list after you have identified the perfect handle for your door. Some styles of handles are not available in all finishes. Always check the technical drawing and dimensions for the item that you want to ensure that you receive the right size and fit.

When you are choosing the new set of lever pad door handles made of upvc, it is crucial to make sure that they correspond to the PZ (distance between the spindle of the handle and the centre of the cylinder hole) of your current multipoint door locks, as these need to be in line for the doors to remain locked, either from the inside or outside. The handles we offer are designed to work with the majority of standard cylinder locks, however you should double glazing window handle-check prior to making a purchase.

You will need to remove the handles on your current handle and remove the lock case if you're upgrading to dual spindle levers for your handle because this will require an additional split inline cylinder. They can be purchased separately and we have the complete technical diagram for you to look at in the images for each product.

It is a good thing to loosen the screws that are holding your existing door handle and then check the mechanism. It is possible that you will need to loosen the screws further in the event that they are not tight, and then you can remove the spindle and handle and put in your new upvc door handle. It is important to ensure that the handle is in the proper position before installing it. You can do this by placing your finger between the door frame and the handle to ensure that it's level.

Lever/Lever

Lever door handles operate a multi point lock using a Euro cylinder. They can be found on a majority of double doors made of aluminium, upvc doors and some wooden doors. They are available in two varieties, with an interior lever and a paddle outside. Sprung - These have a spring cassette installed within the backplate that helps bring the handle lever into a horizontal position. Non-sprung: These do not have a mechanism to spring the handle lever to a horizontal angle.

To fix a door handles and hinges handle lever that is sagging it is necessary to locate the hole or detent access pin. This is usually an insignificant hole or protruding ring, or rectangle, located on the handle base plate. Once you have located it, loosen the set screw with a screwdriver and take it off to allow the lever and return it to the horizontal position.

After the handle is positioned horizontally, you can install the screws. Tighten them to ensure that the handle stays connected to the base plate. Consider applying a threadlocking product to the threads of screws to increase grip and prevent them from loosing over time.

Drooping lever door handles can be caused by many factors. The most common reason is that the fixings are over tightened, and are putting pressure on the bearings that are which causes it to become a bind on the door's face. It could also be because the levers aren't being operated at a straight angle and this is causing compression of the latch mechanism and preventing it from fully springing back into operation.

A common cause of a spring lever not operating properly is the spring not being in the proper position on the backplate. To check whether the handle is back to horizontal, simply operate it.

It is essential to repair any door handles that are loose immediately. This can cause excessive wear on the screws and the handle might be able to fall off the base plate. It is also recommended to tighten loose screws frequently to prevent them from becoming looser.

Lever/Snib

These upvc handles are called 'Snib handle sets' and feature a snib lock button at the top of the door lever. If you don't have a dummy lock device you can use this to secure the door. These door handles are fitted with the Fullex lock 68PZ. (68mm between the spindle and lock centre). We also have a selection of 68PZ door handle from manufacturers such as Ferco and Fab & Fix.

Change your door handle is a cost-effective option to modernize your home, whether replacing your handles or installing new ones to doors you've built in your house. There are a variety of styles of door handle replacement handles made of upvc with traditional levers on backplate, straight or curving short latch and knob handles that resemble dummy knobs for multi point locks that are perfect for French doors.

Lever on backplate handles are typically rectangular in shape, however you can also find oval or circular-shaped models that are referred to as rose door handles. These kinds of door handle replacements handles come with a lever or knob on a backplate, which sits behind the knob or lever and is often referred to as a rosette. However, certain back plates can be detached for concealed fixing.

The handles are available in a variety of finishes including coloured and chrome finishes to match your door and other hardware, such as knobs hinges, and bolts. Some handles have a an grub screw that can be used to connect the knob or lever to the spindle. Some handles are equipped with bathroom spindles which can be used to make bathroom locks. They also have a thumbturn release mechanism, and can be used on bathroom doors.

Mortise

The tubular latch is most likely to be the cause if your uPVC door handle is slammed shut. This can be caused by various reasons, but the most common is an absence of lubrication within the latch plate. This can be resolved easily by simply opening the door and spraying lubricant onto the handle and lock. It could also be that the latch has slipped away from the backplate. This is a more complicated problem that would require the assistance of a specialist.

A multipoint handle is the ideal solution to a stuck door handle. The handles are inserted into the door's faceplate and are operated by an actuated thumb turn knob or key that activates a cam that locks the deadbolt. The handles are available in a variety of different sizes to fit various types of uPVC doors. They are also available in a variety of attractive finishes to match the hardware you already have. The handles are available on the internet or through the local locksmith. They are simple to install and come with clear directions.

You will have to know your PZ size of your cylinder in order to select the appropriate replacement handle set. This is the distance from the edge of the inner frame of the door to the central point of the hole for the handle in millimetres. You should also know if your door has a hook style lock or a mortise lock. The easiest way to find the correct handles once you have the measurements is to use the brand filter on the website. This will narrow down the options and you can then choose the appropriate size from there.

A typical handle set includes the handle unit and a pair of different length screws as well as drill guides and installation instructions. The smart versions, such as the Igloohome Smart Mortise 2+ comes with an entire mortice lock that has an integrated keypad. These are more sophisticated units that are best suited to professional installers or highly competent DIYers. Some handle sets have various other accessories, such as weather strips, which can be used to improve the look of the door.