Replacement UPVC Door Handles

You can find the perfect handle for your door, whether you are replacing your existing handles or adding security. These handles made of upvc replacement door handles are easy to install and meet the minimum 92mm centre distance of multipoint locks.

The most important measurements to take into consideration are backplate fixing centres and key hole dimensions and levers. Check these carefully against your existing measurements prior to placing an order.

Lever/Pad

Lever pad handles for doors consist of a lever handle on one side and a paddle-shaped handle on the other. They are intended for use with key wind locks. However they can also be attached to multipoint split spindle door locks.

Our selection of upvc handle lever pads are available in a range of finishes. They will be listed in the drop-down list after you have selected the perfect handle for your door. Not all styles of handle are available in every finish and you should always look over the technical drawings and sizes sections for the specific product you're looking for to ensure that you are getting the correct size and fitting.

When choosing new lever pad door handles made of Upvc it is essential to ensure that they match the PZ (distance between the spindle of the handle and the center of the hole for the cylinder) of your existing multipoint locks, since they have to be in line to ensure that the doors remain locked, whether from the inside or the outside. The handles we sell are designed to work with the majority of conventional cylinder locks, however you should double-check prior to making a purchase.

If you are looking to upgrade to dual spindle levers, you'll need to take out the existing handles and take apart the lock case. This will require an extra split cylinder inline. These can be bought separately and we offer an entire technical diagram for you to look at in the images for each product.

It is a good thing to loosen the screws that are holding the door handle you have and then check the mechanism. It is possible that you will need to loosen the screws further if they are not tight. Then you can remove the spindle and handle and put in your new upvc door handle replacements handle. Before you screw the handle into the frame, it is recommended to ensure that it is in the correct place. You can do this by putting your finger into the space between the door frame and the door handle to make sure that it is level.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock that uses an Euro cylinder. They are located on many double upvc door handles doors as well as wooden and aluminium doors. They have a lever inside and an outside paddle and are generally available in two varieties. Sprung - These include a spring cassette installed within the backplate to help bring the handle lever into an upright position. Non-sprung - These do not have a spring mechanism, and must be manually pulled to raise the handle lever to a horizontal position.

To fix a door handle lever that is sagging you'll need to locate the hole or detent access pin. It's usually a small hole or protruding ring or rectangular that is located on the base of the handle plate. Once you have located the hole for accessing the detent or pin, you are able to remove it with the help of a screwdriver.

When the handle is in a horizontal position, you can put the screws back in place and tighten them so that the handle is fixed to the base plate. Consider applying a threadlocking solution to the threads of the screw to increase grip and prevent the threads from becoming loose over time.

Lever door handles that droop could be the result of various causes. The most common cause is that the fixings have been over tightened and are putting strain on the bearings that are which causes it to become a bind on the door's surface. It is also possible that the levers have not been operated at a right angle, which stretches the latch mechanism and stops it from fully springing into operation.

A common cause of a sprung lever not working correctly is the spring not being in the proper position on the backplate. The simplest way to check this is to move the handle to see if it returns to its horizontal position.

If the door handles aren't tight, it is essential to spot the issue quickly, since this could lead to excessive wear on the screws and possibly to the handle falling off of the base plate. It is also recommended to tighten any loose screws regularly to stop them from becoming looser.

Lever/Snib

These upvc handles are called "Snib handle sets" and have the snib lock button on the top of the door lever. If you don't have a dummy locking device you can use this device to lock the door. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's center and lever or lock centre) door lock. We also carry a selection of other 68PZ door handles from various manufacturers, including Ferco and Fab & Fix.

The replacement of your door handle is a cheap way to update your home, regardless of whether you're replacing handles that are in use or fitting new ones to doors you've built in your house. There are a variety of upvc door handle available with traditional levers on backplate, curved or straight short latch and knob handles with dummy handles for multi-point locks, that are perfect for French doors.

Lever on backplate handles are often rectangular in shape, however you can also find oval or circular models that are referred to as rose door handles. These handles are identified by a lever or knob that is attached to the backplate. The backplate is removable for hidden fixing.

These handles are available in a variety of finishes, including coloured and chrome finishes to complement your door and other hardware, such as knobs hinges and bolts. Some handles are equipped with a grub screw to attach the knob or lever securely to the spindle. Other handles come with bathroom spindles that can be used to control bathroom locks and feature a thumbturn turn as well as a release mechanism, perfect for use on bathroom doors.

Mortise

If your uPVC front door handle is stuck in the open position, the cause will most likely be with the tubular latch. This could be due to many things however the most frequent is a lack of lubrication in the latch plate. It is possible to solve this problem by opening the door, spraying lubricant on the lock and handle. Alternatively, it could be that the latch plate is separated from the backplate. This could be more problematic and will require a specialist to fix it.

A multipoint door handle is the ideal solution to the problem of a sticking door handle. These handles mount through the door's faceplate and are operated by the thumb turn knob or key which activates a cam that locks the deadbolt. The handles are available in a variety of sizes that will fit different types of uPVC doors. They also come in a variety of attractive finishes to complement the existing hardware. The handles are available on the internet or through the local locksmith. They are easy to install and come with clear directions.

You will have to know your PZ size of your cylinder in order to choose the correct replacement handle set. This is the measurement in millimetres between the inner edge of the door frame and the centre of the hole for the handle. It is also important to determine if the door is hook locks or a mortise style lock. The easiest way to find the correct handles once you know the measurements is to use the brand filter on the website. This will narrow down the options and you can then choose the appropriate size from there.

A typical handle set includes a handle unit, two screws of different lengths, drill guides, and instructions for installation. Smarter versions, such as the Igloohome Smart Mortise 2+ come with a mortice lock with keys. These are more complex devices and are best suited to professional installers or skilled DIYers. Certain handle sets come with various accessories, like weather strips that can be used to enhance appearance of the door.