Reasons Your fiat 500x key 500 fiat a602 key Fob Won't Work

A key fob with the fiat key 500 number is a handy way to open the doors and start the car. However, there are numerous reasons why the key fob might stop functioning. This could be due to a dead coin-battery water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat 500 key fob replacement Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob that isn't working. Modern key fobs have a very limited range of operation, and should be within only a few feet from the vehicle to operate. If you're far from your vehicle and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the coin-cell battery (Part Number CR2032) with a new battery from a reputable brand such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while standing near your fiat Panda key 500. The parking lights should flash and the key fob should operate the lock and unlock switches.

If your key fob doesn't work even after replacing the battery, there may be water damage that hinders it from connecting to the module inside your vehicle. Water damage can occur in many ways, such as simply splashing or submerging the key fob into saltwater at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work, your fob is likely to need to be reprogrammed by a professional auto locksmith or dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean, or wash it in a machine. Saltwater is especially dangerous how to program fiat 500 key fob the circuit board of the fob and can cause it to short out and eventually end up dying. It's not the best idea to get the fob wet however, don't give it up if you accidentally drop it in the water or don't remove it from your pants pocket.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Next try the fob and see if it works. If the fob doesn't work it could need to be reset. This is typically done by a dealer or professional auto locksmith.

If the key is more recent and was not programmed to your vehicle it is likely to need to be replaced completely. A professional locksmith for cars can complete this simple process. The locksmith needs to cut the key to match the ignition in your vehicle. They'll also have to reprogram the fob to your vehicle's system. This is a cost-effective and fast process that can be completed on the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob could stop working is that it's simply out of range. The remote typically has an area of 30 feet or less and if it's far from your car, it won't respond to your commands. It's easy to solve this issue by moving the remote closer to your vehicle until it responds.

If your fob does not work after you replace the coin battery, also called a "button", "watch" or "button" It could be due to an issue with the internal circuit board. In the majority of cases, reprogramming your fob will resolve this issue. You can find the steps for the majority of vehicles on YouTube or in the owner's manual.

It's possible that you need to replace the metal clips that hold the coin battery in place. If they loose tension, it can prevent the battery from being properly seated and cause your remote to malfunction.

In rare cases the fob might be out of connection with your vehicle as a result of software or hardware problems. This could be a huge problem, but you can usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob. In some instances it is possible that the software will require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This could occur if the keyfob's location is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob could not function because of a problem to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting every single system on board in your 500 keys, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will clear any residual electric current, and also restart the computer of your car. This can help get your key fob to function again. If the issue persists you should seek out an expert technician. They will be able to identify the root cause of any issues.