Replacing uPVC Window Handles

It is simple to swap the handles on windows made of Upvc. It is important to ensure that the replacement upvc door handle handle is fitted into the spindle cutout of the window mechanism.

If the steps below are followed correctly If you follow the steps correctly, any cockspur handle can fit most windows. The most important factor is the step in the height of the handle.

What to look for

Over time, uPVC handles and hinges on many windows in the UK may begin to show signs wear and tear. If this occurs, the handle may become loose or difficult to operate, which makes it essential to replace it. This is a simple task that can be accomplished by anyone who is comfortable using basic hand tools.

The first step is to make sure the handle is securely attached to the window frame and in a position that is open. The next step is to locate the fixing pins or screws that keep the handle in the position it is in. These are usually located on the inside of the handle. They can be removed with an screwdriver or pliers.

Once the handle has become loose and sagging, it can be removed from its hinges by gently pulling it off. It is then time to find a replacement handle of the same style and size. This can be accomplished in a DIY store or online. The procedure should take just five minutes, and you will need a screwdriver.

When replacing a uPVC handle it is essential to take into consideration the step height. This is the distance from the bottom of the handle to where it rests on the frame of the window. This is typically an average measurement, but it is essential that you check the step height of your current handle prior to ordering a new one.

There are a variety of sizes based on the kind of handle. Inline handles for uPVC windows generally feature lug centers of 31mm as well as handles with cockspur that have 43mm centres. Tilt-and-turn handles are commonly found on uPVC Windows. They feature a unique design that allows the window to be tilted to allow for ventilation and then turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This makes them difficult to open and is why it is crucial to ensure that the replacement handle you buy has the same length of spindle that your current one.

Remove the old handle

If the handles on your windows are damaged or improperly fitted, they could cause double glazed door handles-glazed windows to close and open incorrectly. They could even become stuck. There are many reasons for this like general wear and tear or corrosion of the metal handle. In these situations it is crucial to locate replacement handles made of upvc immediately to prevent further damage and loss of function.

One of the first steps to do when replacing the handles on your windows made of upvc is to remove the old handle from the window. To do this, begin by getting rid of the screw that is covered when the handle is in its closed position. Once you have removed that screw, you are able to remove the handle. It is possible to make the task easier by using an electric screwdriver.

It is also important to note that the screws on the handle may be hidden behind plastic caps, therefore it is recommended to use a Stanley knife to the screw caps and then take them off. After removing the handle, you will be required to inspect the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. It is important to measure the spindle length on the handle that was used and then compare it with the dimensions of the window mechanism spindle cutout.

There are three kinds of Upvc handles: Espag handles with a central screw that can be turned either left or right and Cranked handles that have two screws, and Spade handles which have arms that are flat and can be used on either side of the upvc window. Once you have a suitable replacement, it's simple to screw the handle in place and ensuring that the spindle is inserted into the lock mechanism. After that, it should be tightened to the window frame, and your new window handles made of upvc must be secure.

Measure the Spindle

If you're replacing a upvc window handle that has come off, it's due to the spindle that holds it in place is loose or damaged. In some cases, you can tighten the spindle with a screw or pin. In certain situations, it may be necessary to replace the handle. There are a few different kinds of window handles made from upvc. There are three types of handles: inline espagnolette cockspur, and tilt-and-turn. Each handle type is installed and replaced in a different way.

Before you purchase a new handle, it is essential to know the size of the handle that is currently in use. This will ensure that the new handle is the correct size and will fit correctly within the window. Fortunately, all handles follow industry standard sizing so it's quite easy to locate the right size.

To determine the size of your handle, first remove it from the window by turning it back to the open position. Then, you should be able to see the size of the screw or pin that is holding it. Then, use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a new spindle that is the same length.

When buying a replacement window handle, it is crucial to take into consideration the step height of the upvc window handle. The step height is the distance from the base of the handle until where it sits on the frame. Typically, this will be about 21mm for uPVC windows and 9mm for Aluminium door handles (apk.Tw). Dropping objects into the space will allow you to observe how far the handle extends before it meets an obstruction.

Cockspur handles typically have different backset heights based on the type of window they are placed in. Inline espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles however they have different backsets depending on the design of the window they are in. This is because they have a spur that extends from their handle and locks onto a cockspur wedge striking plate.

Install the new handle

After you have chosen the new handle, ensure that it is aligned with the holes for screws on the door. Then, secure it with the screws supplied. Install the latch lever in similar fashion to the handle that you are replacing if you are also replacing the door handle. Then, you can reattach the door trim to hide the mounting screws and finish the job.

Tip: To remove a metal head from a wooden wedge place the handle on the floor, so that its wide end is on the ground. Then use an hammer and tap the narrow end. Be careful not to scratch the handle or spindle.