Reasons Your Fiat 500 Key Fob Won't Work

A fiat key replacement cost 500 key fob is a great way to open the doors and start the car. There are a variety of reasons why the fob could stop working. It could be due to a dead battery water damage, receiver module issues, and interference.

This listing is for a NEW replacement fiat 500 new key cost uk 500 key replacement fiat 500 keys derby uk - read more - Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is an inactive battery. Modern key fobs have an operating range that is limited and must be within a few inches of your vehicle to work. If you're far from your vehicle and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery locked keys in car boot fiat punto the coin-cell (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

After you've replaced the battery of your coin cell You can test it by standing near your Fiat 500 and pressing the buttons. The parking lights should blink and the key fob will operate the lock and unlock switch.

If the fob's remote doesn't function after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module inside your vehicle. Water damage can occur in a number of ways, ranging from a light splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If this does not work, you'll need to have your fob reset by an auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it in a washer. Saltwater is particularly dangerous to the circuit board of the fob that can cause it to short out and eventually die. In the event that you let your fob get wet, it's not a good idea however, if you drop it in the water in a cup or forget to remove it from your pants pocket prior to running the washer, don't give up hope.

First remove the battery from the fob. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Next try the fob and check if it functions. If the key doesn't function, it may need to be programmed again. This is usually done by an auto locksmith or dealer.

If the key you have is older and has not been programmed for your car then you'll need to replace it completely. A professional automotive locksmith can do this job. The locksmith needs to cut the key to match the ignition on your vehicle. They will also need to reprogram the fob for your car's system. This is a low-cost and quick process that could be completed on the same day.

Receiver Module Issues

Your 500 key fob might stop working because it is out of range. The remote usually has an area of 30 feet or less and if it's far away from your car it will not respond to your commands. It's easy to solve this problem by moving the remote closer to your car until it responds.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob still won't work it could be due to an internal circuit board issue. In most cases, reprogramming the fob will fix the problem. You can find the steps for the majority of vehicles on YouTube or in the owner's guide.

You may need to replace the metal retaining clips that hold the coin battery. If they loose tension, it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob could be out of alignment with your vehicle because of hardware or software issues. This could cause a significant problem, but you can usually fix it by visiting an auto locksmith to have them reprogram your fob. In some cases, the software may also require reinstallation into your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be able to receive or transmit the signal due to interference. This could happen if the key fob is located near a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob could not function may be a lack of connection to the buttons or damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, located beneath the dashboard, detects radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset every single system on board in your 500, including the key fob. Disconnect the battery of 12 volts for about 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will eliminate any residual electricity and restart the car's computer system, which could help the key fob to function again. If the issue persists, you should consult an experienced technician. They will be able to determine the exact cause of your issues.