Replacing uPVC Window Handles

It is simple to swap the handles on windows made of upvc. It is important to ensure that the new handle is a good fit for the spindle cut out in the window mechanism.

If you follow the steps below any cockspur handle can fit in most windows. The step height of the handle is key.

What to Look For

Over time, uPVC handles on many windows in the UK may begin to show signs wear and tear. When this occurs, the window handle may become loose or difficult to operate, which makes it necessary to replace it. Anyone who is familiar using a basic hand tool can complete this relatively simple task.

The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to locate the fixing pins or screws that keep the handle in the position it is in. They are usually on the inside of the handle and can be removed with a screwdriver or pliers.

When the handle is loose and sagging, it can be removed from its hinges by gently pulling it off. Then, you will need to locate a replacement handle of the same style and size. This can be done at an online store or in a DIY store. The procedure should take just five minutes and a screwdriver is all you need.

When replacing a uPVC handle it is essential to consider the step height. This is the distance between the handle's base and where it is placed in the window frame. This is usually an average measurement, but it is essential that you determine the step height of your current handle before ordering an entirely new one.

Depending on the type of handle you have there are various sizes that are available. Inline handles are offered for uPVC window with lug centres of 31mm, while cockspur handles have lug centres of 43 millimetres. Tilt and turn handles are often found on windows made of uPVC and they come with a unique design that allows windows to be tilted in for ventilation and turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack internally rather than breaking off from the base section. This could make it difficult to open. It is crucial to ensure that the replacement handle has the same spindle that was used in your original one.

Take off the handle from the old one.

A poorly fitted or damaged window handles could cause your double glazing window handles glazed windows to close or open incorrectly, and can cause them to become stuck. There are a variety of reasons for this like general wear and tear or the corrosion of the handle made of metal. In these situations it is crucial to seek replacement window handles made of upvc as soon as you can in order to avoid further damage and loss of functionality.

When replacing upvc windows handles it is recommended to remove the old handles from the window. Begin by removing the screw when the handle in closed position. This will reveal a screw and once removed, you are able to begin to take off the handle itself. It is possible to make the task easier by using an electronic screwdriver.

Be aware that screws can be hidden beneath caps made of plastic. It is recommended to remove the covers using a Stanley knife. After removing the handle, you will need to check the square cutout on the base to make sure that the new handle for the window lock is compatible. This is important as you'll need to measure the length of the spindle on the old handle to make sure it is in line with the size of the window mechanism and the handle spindle that has been cut out.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned left or right, Cranked handles with two screws and Spade handles, which have arms that are flat and can be used either side of the upvc window. When you have a suitable replacement, it is simple to screw the handle in place and ensuring that the spindle is correctly fitted into the lock mechanism. Once that is done then it is time to secure it to the window frame and your replacement window handles made of upvc should be secure.

Take a measurement of the Spindle

If you need to replace a upvc handle that has collapsed, it's likely the spindle holding it in place is damaged or loose. In some cases it is possible to tighten the spindle with pin or screw. In some instances, it may be necessary to replace the handle. There are several types of upvc window handles. These include inline espagnolette handles as well as cockspur handles. tilt and turn handles. Each type of handle is mounted and replaced in a different fashion.

Before you purchase a new handle, it is essential to know the size of the one you have. This will ensure that the handle fits the window in a proper manner and will be of the correct size. Fortunately, all handles follow industry standard sizing so it's quite easy to locate the right size.

To measure the handle's size you must turn the window to the open position. You should be able to see the size of the pin or screw that secures the handle. Use a ruler or a tape measure to determine how long the spindle is. Once you have the length of your spindle it is possible to purchase a replacement that is exactly the same size.

When you are looking to replace a handle you should take into consideration the step height of the window handle made of upvc. The step height is measured from the base to the point at which the handle is positioned on the frame. In general, this is approximately 21mm for upvc door handles windows or 9mm for aluminum. To ensure that the new handle will work the gap, drop something into the space to see how far it extends before it meets an obstruction.

Cockspur handles usually have different backset heights, based on the style of window they're installed in. Inline Espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles have different backsets depending on the type of window they are located in. This is due to the fact that they have a spur that extends from the handle and locks onto a cockspur wedge-striking plate.

Install the new handle

Once you've selected the new handle, make sure it is aligned with the holes for screws on the bifold door Handles. Then, secure it with the screws provided. If you're also replacing the latch lever it can be put in similarly to the victorian scroll door handles handle. Finally, reattach the door trim to hide the mounting screws and close the job.

Tips: To remove the metal head from the wedge of wood Hold the handle so that its wider end is resting on the floor. Use a hammer to tap the thin end of the handle. Be careful not to damage the handle or spindle.